FLEXIBLE HOSES FOR FLUIDS AND GASES: ANACONDA CORRUGATED HOSES TYPE BW656, BW756, BW856, BW956, BW673 & ANAFLEX ■ANAMETEUROPE YOUR PARTNER IN FLEXIBLE SYSTEMS

ANACONDA CORRUGATED METAL HOSEHOSE SELECTION TABLE Hose The end connections for hoses BW656, BW756, BW856, BW956 and BW673 are described on pages 1-11 till 1-24. The self-mountable fittings for ANAFLEX are described on page 1-33. In addition, and on request, we also can supply : - GMA gas meter connection - Fully interlocked (UI) Casing as mechanical hose protection. - Hiprojacket heat protection products. - Rubber hoses for fluids. - Teflon hoses for fluids. - Vibration eliminators. - Expansion joints. This corrugated hose catalogue supersedes all previous corrugated hoses catalogues. Information...

ANACONDA MULTIFLEX® ANACONDA CORRUGATED METAL HOSE ENGINEERING DATA GENERAL INTRODUCTION ANACONDA metal hose is the leader in the flexible hose field since our beginning in 1908. ANACONDA stands for a complete line of flexible products, such as corrugated metal hose, stripwound hose, metal bellows and expansion joints, vibration eliminators, Sealtite electrical wiring conduit and specially designed flexible connectors for many applications. Our leadership in the field was made possible by years of dedication to producing only the highest quality metal hose products available. Strict quality control...

ANACONDA CORRUGATED METAL HOSE ENGINEERING DATA GENERAL HOSE ASSEMBLY DESIGN CONSIDERATIONS - CONTINUED Température As the température of metal hose increases, the pressure capability decreases. The factors shown below should be used to adjust the pressure capabilities at higher temperatures Température correction factors As the service temperature increases, a hose assembly maximum pressure rate decreases. The maximum allowable pressure of the hose assembly shall be the lowest of any method of assembly (mechanical, soldered, welded, silver brazed). By using the factors given in the table on...

ANACONDA MULTIFLEX® ANACONDA CORRUGATED METAL HOSE ENGINEERING DATA GENERAL HOSE ASSEMBLY DESIGN CONSIDERATIONS - CONTINUED Motion movement Length The active or exposed length of a hose assembly must be sufficient to meet the conditions of movement. Lengths shorter than suggested can result in premature fatigue failure. Length tolerances as per our Quality Assurance Programme. Bend Radius The bend radius shown in the various hose tables are adequate to meet most industrial flexing requirements. Consideration should be given to those applications involving levels of high frequency or large amounts...

ANACONDA CORRUGATED METAL HOSE STANDARD UP TO MEDIUM PRESSURE BW 656 Anaconda butt welded corrugated stainless steel hose type BW656 is designed for conveying chemicals, gases, steam, etc. It is suitable for use under full vacuum and has a temperature range of cryogenic to ca. +600°C*. Type BW656 is designed for general purpose service and will meet most pressure requirements. It has a good flexibility and a good flexural strength, suitable for normal industrial vibrations. Burst pressure: The burst pressure of hose with braid is at least 4 times the working pressure. Material spécifications:...

ANACONDA CORRUGATED METAL HOSE MEDIUM PRESSURE & LARGER SIZES Material spécifications: The core is manufactured from stainless steel AISI 316L (1.4404) with a heavy stainless steel AISI 304 (1.4301) wire braid covering. Other alloys are available; consult your Anamet representative. Types: BW756-0 corrugated stainless steel hose, unbraided BW756-1H corrugated stainless steel hose, with one heavy braid BW 756 Anaconda butt welded corrugated stainless steel hose type BW756 is designed for conveying chemicals, gases, steam, etc. It is sui-table for use under full vacuum and has a temperature range...

ANACONDA CORRUGATED METAL HOSE Material spécifications: The core is manufactured from AISI 316 L (1.4404) stainless steel with a heavy stainless steel AISI 304 (1.4301) wire braid covering. Other alloys are available; consult your Anamet representative. Types: BW856-0 corrugated stainless steel hose, unbraided BW856-1H corrugated stainless steel hose, with one heavy braid BW856-2H corrugated stainless steel hose, with two heavy braids HIGH PRESSURE Anaconda butt welded corrugated stainless steel hose type BW856 is designed for conveying chemicals, gases, steam, etc. It is suitable for use under...

ANACONDA CORRUGATED METAL HOSE EXTRA HIGH PRESSURE ANACONDA butt welded corrugated stainless steel hose type BW 956 is designed for conveying chemicals, gases, steam, etc. It is suitable for use under full vacuum and has a temperature range of cryogenic to ca. +600°C*. The engineered design and construction allows it to operate at higher pressures than the BW856 type. Its extra durable construction makes it suitable for severe applications, vibrations and extreme high pressures. Burst pressure: The burst pressure of hose with braid is at least 4 times the working pressure. Material spécifications:...

ANACONDA CORRUGATED METAL HOSE EXTREME CORROSION RESISTANT ANACONDA type BW673 is extremely résistant to corrosion, and is used to convey corrosive liquids and gases for applications that involve high pressure, temperatures up to +540 °C*, vibration and flexure. Type BW673 is designed for Chlorine applications. Applicable as transfer hose for tankcar, cargotank, tankbarge, etc. Burst pressure: The burst pressure of hose with braid is at least 4 times the working pressure. Material spécifications: The hose and braid are manu-factured from Monel 400. For other alloys please consult your Anamet...

ANACONDA CORRUGATED METAL HOSE STAINLESS STEEL BRAIDING Types: S Standard braid E Extra heavy braid (on demand) BRAID Anaconda braid type S (standard braid) and H (heavy braid) are mainly supplied in combination with our Anaconda butt-welded corrugated hoses type BW656, BW756, BW856 and BW956. However they can also be obtained as loose braids. Burst pressure: The burst pressure of hose with braid is at least 4 times the working pressure. Material spécifications: The braids are manufactured from stain-less steel AISI 304 (1.4301) wire. Other alloys are available; consult your Anamet representative....