Vérin sans tige profil plat à accouplement magnétique WRV Jusqu' à 8mm/

Magnet Type Flat Rodless Cylinders WRV Environmentally friendly RoHS compliant product! Unique oval barrel design enables good low-speed performance, low center of gravity, and non-rotating. Low-Speed Performance Basic Type Superior low-speed performance of 8mm/s. Best performance among Magnet Type Plate bumper (urethane rubber) Rodless cylinders. Direct Mounting A block-type end plate makes direct mounting possible. Side surface piping Thin Design Reduced by 30% in height With Shock Absorber Specification Side surface piping Shock Absorber A dedicated linear orifice shock absorber installed....

By installing a sensor rail and sensor magnet, positioning detection across the full stroke range is possible. Before use, be sure to read the “Safety Precautions” on p. . Combines with linear guide to reduce the height to a minimum, and also offers various connection with equipment. Safety Precautions Handling Instructions and Precautions Specification List Order Codes Sensor Switches Available stroke

Always read these precautions carefully before use. Safety Précautions (Flat Rodless Cylinders) Before selecting and using the products, please read all the Safety Précautions carefully to ensure proper product use. The Safety Precautions shown below are to help you use the product safely and correctly, and to prevent injury or damage to you, other people, and assets beforehand. Follow the Safety Precautions for: ISO4414 (Pneumatic fluid power—Recommendations for the application of equipment to transmission and control systems), JIS B 8370 (Pneumatic system regulations) The directions are ranked...

• Avoid scratching the cords for the sensor switch lead wires, etc. Letting the cords be subject to scratching, excessive bending, pulling, rolling up, or being placed under heavy objects or squeezed between two objects, may result in current leaks or defective continuity that lead to fires, electric shocks, or abnormal operation. • Do not subject sensor switches to an external magnetic field during actuator operation. Unintended movements could result in damage to the equipment or in personal injury. • Use within the recommended load and operating frequency specifications. Attempting to use...

Always read these précautions carefully before use. Design and selection Installation and adjustment Warning 1. Check the specifications. As use of this product over the specified ranges of voltage, current, temperature, shocks, etc., could result in a breakdown or abnormal operation, always read the specifications carefully to ensure correct use. 2.Avoid mounting actuators in close proximity. Mounting two or more actuators with sensor switches in close proximity could result in erratic operation of the sensor switches, due to magnetic field interference with the system. 3. Caution about sensor...

When the actuators with sensor switches are moving, or when moving objects are nearby, do not let them come into contact each other. In particular, lead wires could become worn out or damaged, causing operating instability in the sensor switch. In the worst case, it could result in current leaks or electrical shocks. 2. Always turn off the power supply for wiring work. Conducting wiring work while the power is on could result in electric shocks. Also, incorrect wiring could damage sensor switches in an instant. Turn on the power only after the wiring work is completed. Warning 1.Check the Catalog,...

SélectionAllowable load and moment^ Although the Flat Rodless cylinders can be used with directly applying loads, make sure that the load and moment do not exceed the values in the table below. In addition, since load capacity may vary depending on the speed, confirm the rubber bumper and shock absorber absorption capacity on p. before use. Caution: The moment including the inertial force generated when the load is moved or stopped must not exceed the values in the above table. Keep the mass and speed within the range of the rubber bumper and shock absorber capacity graphs. Note: W is the maximum...

Slider deflection The reference values of the amount of slider deflection due to clearance is shown in the table below. Since the slider portion of the Flat Rodless cylinder allows a certain amount of play as shown below, use the cylinder with a linear guide in high-precision applications. Cushioning capacity Rubber bumper capacity The Flat Rodless cylinders come with rubber bumpers as standard equipment. The maximum load capacity and impact speed, however, should lie within the “With rubber bumper” range shown in the “Rubber bumper and shock absorber capacity graph” below. Do not use it when...

Handling Instructions and Precautions Calculation of impact energy Horizontal impact Vertical impact Note 1 When descending When ascending Note 1: For impact on incline, g L sin . E3 becomes E3 = m・ ・ ・ Note 1: For impact on incline, E 3 becomes E 3= W ・ ・ L sin . Note 2: When descending, heavier loads can be carried using lower operating air pressure (P) than when ascending. E ：Total impact energy [J] m･ E1 ：Kinetic energy [J] 2 E2 ：Additional energy by cylinder thrust Fo·L [J] E3 ：Additional energy by load mass m·g·L [J] m ：Load mass [kg] ：Impact speed [m/s] g ：Gravity acceleration 9.8 [m/s2]...

Mounting Mounting^ 1. Because the Flat Rodless cylinders have strong magnets built into the cylinder bodies, they cannot be used in locations with magnetized cutting oil or powder. 2. Be careful to avoid making scratches, dents, etc., on the cylinder barrel. 3. If an external force larger than the magnetic retaining force is applied, causing the slider and piston to deviate or completely separate, return the piston to the stroke end and then apply external force to the slider to restore it to the correct position. 4. When using in locations where the cylinder can easily become smeared, clean...