COLMANT CUVELIERrps member of SANOK RUBBER CROUP 02-2018 © COURROIES VECO SYNCHRO Pas L et H © VECO SYNCHRO BELTS Pitches L and H 12001 -1 / 3 Fiche Technique - TechnicaL Data Sheet Courbes d'allongement des courroies en fonction de la tension pour les largeurs standard BELTS ELONGATION BASED ON TENSION FOR STANDARD WIDTHS Tensions de travail admissibles (daN) Allowable working tensions (daN) mambar of SANOK PUBB

COURROIES VECO® SYNCHRO Pas L et H VECO® SYNCHRO BELTS Pitches L and H 12001 - 2 / 3 COURBES D’ALLONGEMENT DES COURROIES EN FONCTION DE LA TENSION POUR LES LARGEURS STANDARD BELTS ELONGATION BASED ON TENSION FOR STANDARD WIDTHS Pas 8 mm / Pitch 8 mm Pourcentage d'allongement Percent elongation 1000 1500 2000 Tension de la courroie (daN) Belt tension (daN) Pas 14 mm / Pitch 14 mm Pourcentage d'allongement Percent elongation

COURROIES VECO® SYNCHRO Pas L et H VECO® SYNCHRO BELTS Pitches L and H 12001 - 3 / 3 Fiche Technique - TechnicaL Data Sheet 02-2018 Tensions de travail admissibles (daN) Allowable working tensions (daN) member of SANOK RUBB

TIMING BELT VECO HTB 8M / 14M Features 12002 -1 / 3 Fiche Technique - Technical Data Sheet COLMANT CUVELIERrps member ofSANOK RUBBER GROUP 02-2018 Function Flexible link between the motor and the machine: • no slip • low and high speed • important capacity of load • allow to transmit high torque (replace transmission by chain with more advantages) • no noise and no maintenance Conception Endless timing belts Synchro HTB, teeth with curvilinear profile, made of : • glass fibre reinforcement which resists to tightening and elongation • mix of neoprene rubber • moulded teeth precision which guarantees...

TIMING BELT VECO HTB 8M / 14M Features 12002 -2 / 3 Fiche Technique - Technical Data Sheet COLMANT CUVELIERrps member afSANOK RUBBER GROUP • The diameter of the pulleys must not be less than the width of the belt. • The speed belt must not be more than 33 m/s. Otherwise, call us. • If the centre distance is more than eigth times the diameter of the small pulley, the both pulleys must be flanged. • Protect the belt against chemicals products. • The life time of the timing belt VECO HTB is minimum 4000 hours in a normal use. • During the stocking, the belts must be protect from humidity, externe...

TIMING BELT VECO HTB 8M / 14M Features 10001 -3 / 3 Fiche Technique - TechnicaL Data Sheet 02-2018 • Non adiusting center distances : Tensioning rollers are not recommended but you can use ther if you follow these conditions : - The roller will be set on the soft part - If possible inside the belt (see figure 1) - The diameter of the roller must be more than 1,33 times the diameter of the small pulley. - It must be corrected if its diameter is smaller than the diameter of a pulley with 40 teeth. - The arc of contact done by the belt must be as smallest as possible member ofSANOK RUBB

COLMANT CUVELIERqps member afSANOK RUBBER GROUP 02-2018 TIMING BELTS VECO SYNCHRO HTB Selecting the transmission 12003 -1 / 8 Fiche Technique - Technical Data SheetDrive caracteristic - Motor - Motor shaft diameter - Driven appliance Nr - driven components speed - driven shaft diameter - Centre distance - Using time - Tensioning type K1 - Corrected factor following the K2 - Corrected factor following the K3 - Corrected factor following the speed (only in case of multiply driver) Example : Electric motor with roller cage - Short circuit starting 30 kW/40 ch 1 450 rpm 55 mm Ceentrifugal fan 24...

TIMING BELTS VECO SYNCHRO HTB Selecting the transmission 12003 -2 / 8 Fiche Technique - Technicat Data Sheet 02-2018 K2 determination: Select the K2 factor on the table below following the working time of the machine we can use: small pulley diameter n1mini : 32 teeth big pulley diameter n2 : 32 x 1,51 = 48 teeth the pulleys 32 et 48 teeth 14 M are standards membar of SANOK RUBB

TIMING BELTS VECO SYNCHRO HTB Selecting the transmission 12003 -3 / 8 Fiche Technique - Technicat Data Sheet 02-2018 Belt length • Select the length belt in using the pitch 0 of the pulleys and centre distance E required. L = 2 E + 3,14 (D + d) D : Pitch diameter of the big pull^r d : Pitch diameter of the small pulley • Choose in the table the closer belt length. • Calculate the exact centre distance E' : E' = E - if Lp < L and E'= E + if Lp > L Belt width • On the following table of transmission power determinate the belt width in accordance with the small pulley and with his speed. (TDS n°12003-4,...

TIMING BELTS VECO SYNCHRO HTB Selecting the transmission 12003 - 4 / 8 Fiche Technique - TechnicaL Data Sheet 02-2018 Transmissible power (in KW) trough timing belts 8 M 20 Speed of the small pulley in rpm Use the transmission only if a diminution of the life time is admissible member of SANOK RUBB

TIMING BELTS VECO SYNCHRO HTB Selecting the transmission 12003 - 5 / 8 Fiche Technique - Transmissible power (in KW) trough timing belts 8 M 50 COLMANT CUVELIERrps member of SANOK RUBBER GROUP 02-2018 Use the transmission only if a diminution of the life time is admissible. Transmissible power (in KW) trough timing belts 8 M 85 Speed of the small pulley in rpm

COLMANT CUVEUERrps member of SANOK RUBBER GROUP 02-2018 TIMING BELTS VECO SYNCHRO HTB Selecting the transmission 12003 - 6 / 8 Fiche Technique - Transmissible power (in KW) trough timing belts 14 M 40 member of SANOK RUBB

COLMANT CUVEUERrps member of SANOK RUBBER GROUP 02-2018 TIMING BELTS VECO SYNCHRO HTB Selecting the transmission 12003 - 7 / 8 Fiche Technique - Technical Data Sheet Transmissible power (in KW) trough timing belts 14 M 85 member of SANOK RUBB

TIMING BELTS VECO SYNCHRO HTB Selecting the transmission 12003 - 8 / 8 Fiche Technique - Technical Data Sheet 02-2018 Transmissible power (in KW) trough timing belts 14 M 170 Speed of the small pulley in rpm Use the transmission only if a diminution of the life time is admissible member of SANOK RUBB