1. Catalogues
  2. Creasol
  3. Creasol UniRec2

Creasol UniRec2

Creasol UniRec2

Résumé du catalogue produit
Introduction : Le Creasol UniRec2 est un récepteur universel multifréquence à 2 canaux, compatible avec divers types de télécommandes en AM et FM. Il peut recevoir sur des fréquences allant de 433.42 à 434.42 MHz, 868.3 à 868.8 MHz, et 288 à 418 MHz (hors UE), et gérer jusqu'à 1000 télécommandes.
Spécifications techniques : Fonctionne avec une alimentation de 7 à 36 Vdc ou 7 à 27 Vac, avec une consommation maximale de 90 mA. Les sorties relais supportent une charge maximale de 5A et une tension de 30Vdc ou 250Vac.
Installation : Doit être installé dans un environnement approprié, idéalement dans un boîtier IP65 en cas d'humidité. Une antenne externe et des fusibles de protection sont recommandés.
Configuration : Préconfiguré pour 433.92 MHz en AM, modifiable via le bouton Prog. Plusieurs modes de sortie disponibles : action maintenue, bistable, et temporisé.
Apprentissage et suppression des télécommandes : Les télécommandes doivent être apprises pour activer les relais. Possibilité de suppression individuelle ou totale, avec réinitialisation aux paramètres d'usine.
Sécurité et garantie : Ne convient pas pour des systèmes de haute sécurité antivol. Installation par un technicien qualifié requise. Garantie limitée aux défauts de fabrication.
Conformité CE : Conforme à la directive 2014/53/UE, déclaration disponible sur le site de Creasol.
Procédures : Programmation standard : Sélectionnez le canal 1 avec 'Prog', puis utilisez les télécommandes pour l'apprentissage. Programmation avec fonction OFF : Sélectionnez le canal 1 avec fonction OFF, puis procédez à l'apprentissage.
Recommandations : Assurez-vous que les télécommandes sont à portée et suivez attentivement les étapes pour éviter les erreurs.
Voir plus

Extraits du catalogue

Creasol UniRec2-1

Multi-frequency 2ch receiver Works with almost any remote control, fixed and rolling code, AM and FM. Multifrequency universal receiver with 2 relay outputs, 250V 5A max. Receives in 1 or 2 frequencies, selectable by the user, AM/FM: 433.42, 433.92, 434.15, 434.42, 868.3, 868.5, 868.8 MHz, 288-418MHz. Smart Home solutions http://www.creasol.it ENGLISH Introduction: this 2 channels universal receiver is able to work with different kinds of remote Controls, fixed and rolling code, AM (OOK) and FM (FSK), even if they operates in 2 different frequencies and/or different modulations. Up to 2 frequencies and modulations can be selected by the user so, for example, it's possible to use the receiver at 433.92MHz OOK, 868.3MHz FSK, or both 433.92MHz OOK and 868.8MHz FSK. Remote controls should be learned into the receiver, so when a programmed code is received the corresponding relay output is activated. It can be used to replace a non-operational receiver, a rolling code receiver or it can be used to add a new frequency to an existing receiver. Also it can be used to control one or two actuators by a remote control, e.g. lights, small motors/pumps, or UP/DOWN roller shutter motor: in this case set parameter 7 to 4 to prevent that UP and DOWN motors can be enabled simultaneously. Relay outputs are protected by overvoltage by varistors. It supports up to 1000 different remote controls (the number depends by the type/length of the transmitted code) and codes/configuration can be saved to/read from an optional/removal memory, so it's possible to move the configuration to another receiver easily. It also supports “master remote controls”, that are not used to activate the output, but to enable programming new remote controls for that output without the need to physically access the receiver. Installation: device should be placed in a proper environment: in case of high humidity, place inside an IP65 case. Connect external antenna (coaxial cable) as indicated in the silkscreen, or a single wire on the left-side screw connector, with length equal to 8cm for 868MHz, 17cm for 433MHz or 25cm for lower frequencies. Connect through protecting fuses both the the power supply and relay outputs! Configuration: this device is supplied pre-configured to receive at 433.92 MHz, AM modulation.To modify this configuration, press quickly the button Prog a number of times corresponding to the programming channel (if needed), the parameter number and the desired value, as shown in the figure. If programming fails, a long red flash is emitted. In hold-to-run mode the output is active until the button on remote control is released. In bistable mode, the remote control button is used to toggle the output ON-OFF-ON-OFF. In bistable ON/OFF mode, one button is used to switch output ON, and another button to switch output OFF. In timer modes, normally it's needed only a button to switch output ON for the programmed time: if the button is pressed again while output is ON, after more than 10s, the output is switched OFF. For any bistable or timer mode, it's possible to program one or more remote controls that are capable to only switch output OFF: follow the instructions below, selecting channel 3 (OFF function corresponding to channel 1) or 4 (OFF function corresponding to channel 2). Learning remote controls: press the Prog button 1 or 2 times, corresponding to the selected channel, or 3 or 4 times for the corresponding OFF functions: Led goes solid green. Press Prog twice to enable learning mode: Led starts flashing slowly. Press a button on the remote controls that should be learned. Every time a new code is learned, the 10s timeout is reload and Led flashes twice if the code is programmed, 3 times if was already learned, 6 times if memory is full. During the learning process, the receiver sensitivity is reduced to avoid the possibility of learning unwanted remote control transmitting from a distant location. Anyway, be careful about this. Removing remote controls: press the Prog button from 1 to 4 times, corresponding to the selected channel: Led goes solid green. Press Prog 3 times, then press button on remote controls in the same way as learning procedure. Led flashes 4 times for any removed code. To remove all remote controls from memory, press the Prog button 10 times, wait for Led flashing, then press Prog button 3 times; press button 4 times instead of 3 to also do a factory reset (default configuration). Learning master remote controls: press the Prog button 1 or 2 times, corresponding to the selected channel: Led goes solid green. Press Prog 4 times, then press button on remote control: this remote controls will not activate the output, but can be used to enable learning procedure without the need to access the receiver and press Prog button. To learn new remote controls in this way, put the master remote control in trasmission for 2s, then keep in transmission for 2s the new remote controls that should be learned: every time a new remote control is learned, the 10s timer is reload to permit successive learnings. Security and safety: do not use in systems that require a high level of anti-theft security. Installation should be done by a qualified technician, in a well insulated enclosure, protected by dust, high humidity, steam and contact with other circuits and metal parts. All responsibility, for any damage caused by not complying with the instructions in this manual, is declined. Warranty: complies with statutory requirements, and covers only defects, within the product itself, in material and manufacture. Your local stockist should be contacted in connection with any warranty-related matters. CE Declaration of Conformity: Creasol hereby declares that this receiver UniRec2 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Declaration of Conformity can be obtained from http://www.ce.creasol.it

 Ouvrir le catalogue en page 1
Creasol UniRec2-2

Press Prog' Led shows Press Prog Led shows current value 3 times new setting (2=433MHz) (3=868MHz) for channel 2 Configure channel 1 in hold-to-run mode (default:timer 500ms) Press Prog Press Prog Led shows Press Prog Led shows 1 time 6 times current 1 time new setting (select ch.1) (parameter) setting (hold-to-run) Program two remote controls on channel 1 and terminate learning Press Prog Press Prog TX remote Learned! TX Learned! Press 1 time 2 times remote R.C.2 Prog to (select ch.1) (start learning) control 1 exit Program two remote controls on channel 1 as OFF function Press Prog Press Prog...

 Ouvrir le catalogue en page 2

Tous les catalogues et fiches techniques (PDF) Creasol

  1. CreasolCatalog

    22  Pages

* Les prix s'entendent hors taxe, hors frais de livraison, hors droits de douane, et ne comprennent pas l'ensemble des coûts supplémentaires liés aux options d'installation ou de mise en service. Les prix sont donnés à titre indicatif et peuvent évoluer en fonction des pays, des cours des matières premières et des taux de change.
À propos de DirectIndustry
DirectIndustry est une marketplace qui offre aux acteurs B2B une expérience complète, du sourcing produit à l’achat. DirectIndustry est une entité de VirtualExpo Group.