

Extraits du catalogue

Incrémental Rotary Encoder G58 Hollow shaft: Type W ■ Housing diameter: 58 mm ■ Shaft: 0 6 ... 10 mm ■ Hollow shaft: 0 6 ... 14 mm ■ Line counts: 2 ... 10.000 ■ Output signals: RS422, PP, TTL, OC, 1Vpp, 11|jApp ■ Connector or cable output: axial or radial
Ouvrir le catalogue en page 1
Incremental Rotary Encoder G58 Dimensions (mm) G 58 S � improved vibration upon request � optional: sealed bearing � optional: shaft seal � connector output: radial or axial � cable output: radial or axial � 2 optional: servo clamps others upon request � improved vibration upon request � optional: sealed bearing � optional: shaft seal � connector output: radial or axial � cable output: radial or axial � 2 optional: servo clamps ∅ d = 6f7 others upon request G 58 H � improved vibration upon request � standard: sealed bearing � connector output: radial or axial � cable output: radial or axial...
Ouvrir le catalogue en page 2
LTN Incrémental Rotary Encoder G58 Version: QI = 11 |jApp at 1 kOhm load SI = 1 Vpp at 120 Ohm load Zero signal Z: (effective)
Ouvrir le catalogue en page 3
LTN Incrémental Rotary Encoder G58
Ouvrir le catalogue en page 4
Incremental Rotary Encoder G58 Recommended input circuitry of subsequent electronics LD and IX: Line driver RS 422 A Operating voltage: Current requirement: Output signals: Max. output frequency: 5 V ± 5 % oder 8 ... 30 V max. 180 mA (without load) A, A, B, B, Z, Z 300 kHz for LD 400 kHz for IX Min. edge separation: Level (RS422): TFL ≥ 0,25 µs (400 kHz) VH ≥ 2,5 V (IH = -20 mA) VL ≤ 0,5 V (IL = 20 mA) Imax: ±20 mA per output TV ≤ 50 ns rise / fall times: ≤ 100 ns max. 100 m -10 °C ... +80 °C Reccommended input circuit Max. current load cap.: Delay time: Switching times: Cable length:...
Ouvrir le catalogue en page 5
LTN Incrémental Rotary Encoder G58 LTN Incrémental Rotary Encoder G58 LTN Servotechnik GmbHOrdering informationIncrémental Rotary EncoderModel series Mechanical specification S = Type S D = Type S + higher vibration capability L = Type L E = Type L + higher vibration capability Shaft- or hollow shaft configuration S = Standard 6 mm for G58L, G58S S = Standard 10 mm for G58H S = Standard 6 mm for G58W H = Type H T = Type H + higher vibration capability W = Type W (shaft mounting with torque coupling) others upon request 5.2 Output circuit LD = Line driver; RS422 IX = LD with interpolation PP...
Ouvrir le catalogue en page 6Tous les catalogues et fiches techniques (PDF) SERVOTECHNICS
-
Collecteur tournant SC 020
2 Pages
-
SM050
2 Pages
-
G24
4 Pages
-
G36
6 Pages
-
G1B
6 Pages
-
SC012
2 Pages
-
Collecteur tournant SM 070
2 Pages
-
Collecteur tournant SM 034
2 Pages
-
Collecteur tournant SC 100
2 Pages
-
Collecteur tournant SM 050
2 Pages
-
SC 100
2 Pages
-
SLIP RING SC 080
2 Pages
-
RE 15
2 Pages
-
RE 10
2 Pages
-
RE 08
2 Pages
-
SC100
2 Pages
-
RE27
2 Pages
-
RE35
2 Pages
-
Resolver size: RE-08
2 Pages
-
Resolver
8 Pages
-
SD
1 Pages
-
SH085
2 Pages
-
G71
6 Pages
-
G36W
6 Pages
-
SC104
2 Pages
-
SC080
2 Pages
-
SC040-M
1 Pages
-
SC020-R
4 Pages
-
SC020
2 Pages
-
SC 100
2 Pages
-
SC 080
2 Pages
-
SC 040 M-series
1 Pages
-
SC 020
2 Pages
Catalogues archivés
-
LTN slip rings
2 Pages
-
LTN resolver
8 Pages